Additional Information

 

 

What are your concepts on A Step-by-Step Guide to Installing a Bathtub?

Mounting a bath tub isn't exactly brain surgery, but it does need strong plumbing, carpentry, and also occasionally, tiling skills. Changing an old bathtub with a new one is likewise a reasonably challenging project. If the old bathtub is readily easily accessible, the task can move easily; if you have to open up a wall surface to get rid of the old tub and also position the brand-new bathtub, the task is a lot harder. In either situation, the task is within a home handyman's abilities, although you will need an assistant to move out the old bathtub and also set in the brand-new one. See to it you have actually qualified yourself for the task and also are comfortable attempting it. As opposed to working with a contractor to take over a halfway-completed project, it is much better to think about using one prior to you begin. Chances are you may require a specialist plumber to make tube connections.
This article will assist you mount a brand-new bath tub in your bathroom if you have already purchased a brand-new bathtub and also do not need to change the arrangement of your previous supply of water pipelines.
Your devices and product list must make up the following:

 

• New Tub


• Hammer


• Pipe Wrenches


• Prybar


• Safety Glasses


• Level


• Pliers


• Adjustable Wrench


• Putty Knife


• Screwdriver


• Cold Chisel


• Tape Measure


• Pipeline Caps


 

Planning for the Installment

First of all, the supporting framework provided with the bath must be fitted (if needed) according to the maker's directions. Next off, fit the faucets or mixer to the tub. When suitable the faucet block, it is very important to make certain that if the tap includes a plastic washer, it is fitted between the bath and the taps. On a plastic bathroom, it is additionally reasonable to fit a sustaining plate under the faucets system to avoid stress on the bath tub.
Fit the versatile faucet ports to the bottom of the two taps using 2 nuts and olives (occasionally provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and then pass the outlet via the hole in the bathroom. Utilize the nut supplied by the producer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the flexible overflow pipeline to the overflow outlet. After that, screw the pipe to the overflow face which must be fitted inside the bath. Ensure you use every one of the provided washers.
Connect the catch to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Attach all-time low of the overflow tube in a similar manner.The bath need to currently be ready to be fitted in its last setting.

 

 

Removing Old Taps

If you need to replace old faucets with new ones as a part of your installation, after that the first thing you must do is detach the water supply. After doing so, switch on the taps to drain pipes any type of water remaining in the system. The procedure of eliminating the existing taps can be fairly troublesome due to the limited gain access to that is frequently the instance.
Use a container wrench (crowsfoot spanner) or a tap device to undo the nut that connects the supply pipelines to the taps. Have a towel ready for the continuing to be water that will come from the pipelines. Once the supply pipelines have been gotten rid of, utilize the very same tool to loosen the nut that holds the taps onto the bath/basin. You will require to quit the single taps from transforming throughout this process. When the faucets have actually been removed, the holes in the bath/basin will certainly need to be cleaned of any type of old securing substance.
Before proceeding to fit the brand-new faucets, contrast the pipe connections on the old faucets to the brand-new taps. If the old taps are longer than the new faucets, after that a shank adapter is needed for the new taps to fit.

 

 

Setting up the Bath tub

Making use of the two wooden boards under its feet, put the tub in the called for placement. The wooden boards are useful in uniformly spreading out the weight of the bath tub over the location of the boards as opposed to focusing all the weight onto four little points.
The following objective is to make certain that the bath tub is leveled all round. This can be achieved by checking the level and adjusting the feet on the bathtub until the spirit level checks out degree.
To set up faucets, fit all-time low of the outermost adaptable faucet adapter to the appropriate supply pipe by making a compression join; then do the same for the other tap.
Switch on the supply of water as well as inspect all joints as well as new pipework for leaks as well as tighten them if required. Fill up the tub and likewise inspect the overflow outlet as well as the typical outlet for leaks.
Finally, fix the bath paneling as described in the manufacturer's user's manual. Tiling and also securing around the bathtub ought to wait up until the tub has actually been made use of at least when as this will settle it into its final setting.

 

 

Fitting New Taps

If the tails of the new taps are plastic, then you will need a plastic connector to prevent damage to the thread. One end of the connector fits on the plastic tail of the tap and also the various other end gives a link to the existent supply pipes.
If you require to fit a monobloc, after that you will certainly call for lowering couplers, which attaches the 10mm pipeline of the monobloc to the common 15mm supply pipe.
Next, position the tap in the placing opening in the bath/basin making certain that the washers are in place in between the faucet as well as the sink. Protect the tap in place with the manufacturer provided backnut. As soon as the tap is securely in place, the supply pipelines can be attached to the tails of the faucets. The taps can either be connected by using corrugated copper piping or with regular faucet ports. The former type needs to be linked to the tap finishes initially, tightening up only by hand. The supply pipes can later be connected to the other end. Tighten up both ends with a spanner after both ends have actually been linked.

 

 

Tiling Around the Tub

In the area where the bath meets the floor tile, it is essential to secure the accompanies a silicone rubber caulking. This is very important as the fitting can move enough to fracture an inflexible seal, triggering the water to permeate the wall in between the bathroom as well as the tiling, resulting in complications with moisture and feasible leakages to the ceiling below.
You can pick from a range of coloured sealants to assimilate your fixtures and also installations. They are sold in tubes and cartridges, and can sealing gaps approximately a size of 3mm (1/8 inch). If you have a larger gap to load, you can fill it with twists of drenched paper or soft rope. Remember to constantly fill up the bathtub with water prior to securing, to allow for the activity experienced when the bathtub is in usage. The sealer can crack rather very early if you do not consider this activity prior to sealing.
Conversely, ceramic coving or quadrant ceramic tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are additionally quickly available on the marketplace. It is recommended to fit the floor tiles utilizing water-resistant or water resistant adhesive and also grout.

 

A Step-by-Step Guide to Installing a Bathtub

 

Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.

But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.

This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.

 

Remove the Existing Bathtub

 

To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.

The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.

 

Choose the Right Bathtub

 

The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.

 

Install the Plumbing and Ledger Board

 

You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.

Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.

 

Install the Bathtub

 

When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.

Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.

If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.

 

Hook up the Plumbing

 

Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.

 

Install the Bathtub Surround

 

A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.

Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.

If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.

If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/

 

I am just very intrigued by How to Install a Bathtub Yourself and I'm hoping you enjoyed the entire blog posting. Sharing is nice. Helping people is fun. Thanks a lot for going through it.

Request Appointment